How Should I Grind Brazilian Coffee For Instant Coffee?

Fine does not mean one thing here, because “instant coffee” means two very different projects. The grind you need depends on whether you plan to mix powder straight into hot water, or brew a concentrate and dry it.

That choice is the single decision that sets your target particle size. Get it right first, then set the grinder.

The Short Answer: It Depends on Which “Instant” You Mean

Ground coffee is about 70% insoluble cellulose fiber, so raw grounds will not truly dissolve in water no matter how finely you grind them. Real instant coffee is made by extracting the soluble solids with hot water, then drying that liquid concentrate into crystals. There is a shortcut, often called microground coffee, where you grind so fine the powder stays suspended in the water instead of settling out. Starbucks VIA is the best known example of this style.

Use the table below to choose your target grind for each production path.

Target Preparation Starting Particle Size Feel/Texture Reference
Microground suspension (mix straight into water) Extra fine, under about 150 microns (aim below 100) Flour or powdered sugar
Hot concentrate for drying into instant crystals Medium fine, roughly 300 to 500 microns Table salt or fine sand
Cold brew concentrate for drying Coarse, roughly 800 to 1200 microns Kosher salt or breadcrumbs

These micron bands follow the Specialty Coffee Association (SCA) grind sizing categories, which define Extra Fine/Turkish powder at under 150 micrometers, Medium-Fine at 300 to 500 micrometers, and Coarse at 800 to 1200 or more.

For most home projects, Path A is the practical one: grind your Brazilian beans to a Turkish-style powder and mix directly with hot water. That is as close to “instant” as grinding alone can get you.

Why Brazilian Beans Need a Slight Change to Your Settings

Brazilian coffee is grown at lower altitudes, commonly around 800 to 1,200 meters, and mostly dry-processed (natural) or pulped natural. That combination matters at the grinder.

According to Espresso Coffee: The Science of Quality (Illy and Viani, Elsevier), low-grown Arabicas such as standard Brazilian naturals have lower cell wall density and higher cellular porosity than washed hard-bean coffees. The authors note these beans fracture at lower stress levels and produce a significantly higher proportion of fines during grinding.

In plain terms: softer beans shatter less cleanly, so you get more dust than you would with dense high-grown Ethiopian or washed Colombian beans.

The practical fix is to shift one or two small steps coarser than you would set for those denser beans, then let your sieve or taste test confirm. When you are grinding for a hot or cold concentrate (Path B or C), this slightly coarser setting keeps the fines count down so extraction stays clean and bitter flavors stay in check.

Brazilian naturals also carry more sugars and oils from dry processing, and that surface friction can cause clumping and burr heating during long grinding runs. If your grinder has adjustable speed, running at a low RPM reduces that heat.

Grinding in short bursts and letting the burrs cool between runs achieves the same thing on a fixed-speed grinder.

Grinder Choice for This Job

A blade grinder is the wrong tool here, because blades chop instead of crushing, which produces a jumble of boulders and dust rather than a narrow, even distribution. You need burrs for any of the three paths.

For extra fine powder, a dedicated Turkish-style grinder or a stepless espresso grinder at its finest zero point is the right choice.

If you want one versatile burr grinder that covers concentrate grinding and daily brewing, a conical burr hand grinder or entry electric burr grinder like the Baratza Encore ESP is a reasonable starting point, though its finest settings are coarser than true Turkish range.

For the powder path, a manual Turkish coffee grinder with hardened steel burrs reaches the sub-100-micron range far more reliably than most espresso grinders.

Optional but recommended: a 100 micron laboratory sieve lets you remove gritty larger particles from microground powder before use.

  • Burr type: conical or flat steel burrs, never blades
  • Target for powder path: under 100 microns after sieving
  • Target for concentrate paths: 300 to 500 (hot) or 800 to 1200 (cold) microns
  • Adjustment: one to two steps coarser than settings for dense washed coffees

Step by Step: The Microground Powder Method

Rest your roasted Brazilian beans for 7 to 10 days after roast first, so excess CO₂ has purged and the grounds will not clump as badly.

Grind to the finest setting your burr grinder can hold, then sieve the powder through a 100 micron mesh and regrind anything that stays on top. Mix 1 gram of powder per 100 mL of water just off the boil (93 to 96°C). Expect a full-flavored cup with some sediment at the bottom. That is normal for suspension coffee, not a flaw. If the cup tastes harsh or overly bitter, that is a common sign the grind went too fine and too much surface area extracted too fast.

That simple one-gram ratio is also why freshness matters before grinding. Older staled beans present the same grind with noticeably flatter results. We cover timing in detail in our guide to Brazilian coffee freshness for instant coffee.

Step by Step: The True Instant Crystal Method

This is the real process industrial producers use, miniaturized. According to Coffee Technology (Sivetz and Desrosier, AVI Publishing), the foundational engineering text for soluble coffee manufacturing, commercial percolation batteries use a medium-to-coarse uniform particle around 600 to 1,100 microns with minimal fine dust to prevent pressure drops and channeling. At home scale, the SCA medium-fine band of 300 to 500 microns is the practical compromise for a pressurized or AeroPress-style extraction.

Brew a dense concentrate at roughly 1 gram of coffee to 4 or 5 grams of water, using a Moka pot, an inverted AeroPress, or a pressurized portafilter. Our AeroPress grind guide for Brazilian coffee covers that brewer’s settings in detail.

Then dry the concentrate. Freeze it into thin sheets and sublimate them in a freeze dryer over about 24 hours, or spread thin layers on silicone mats in a convection oven at its lowest setting (about 50 to 60°C) until the moisture drops below about 3%.

Crush the dry sheets into flakes. Those flakes dissolve fully in hot water, because they are pure soluble solids with no cellulose left in them. This route takes real equipment, but coffee brewed for cold concentrates starts from a very different grind, which we detail in our Brazilian coffee cold brew grind guide.

Troubleshooting by Taste and Texture

Sediment in a powder-path cup is expected, but a gritty mouthfeel means particles larger than your target survived the grind. Sieve tighter.

A weak, thin cup from a powder-path brew usually means coarser particles than you think, so run the grinder finer and sieve again. A harsh, bitter cup usually points the other way: too much fines and too much extraction, made worse by soft Brazilian naturals. One small step coarser on the grinder fixes it more reliably than changing dose.

This is the core insight worth carrying: with low-density Brazilian beans, grind size and fines control interact more strongly than dose does, so fix texture problems at the grinder first.

The Bottom Line

Grind Brazilian coffee under about 100 to 150 microns (flour-fine) for microground suspension coffee, or 300 to 500 microns if you plan to brew a concentrate and dry it into true instant crystals. Rest the beans 7 to 10 days post-roast, run burrs not blades, and step one notch coarser than you would for dense washed coffees. Then mix one gram per 100 mL of hot water and taste your way to the exact setting. For brewed cups with your leftover beans, our espresso grind guide for Brazilian coffee is the natural next stop.